Hard to Pick Out Suitable End Mills? These Basics May Help

The main cutting edge of the end mill is a cylindrical surface, and the cutting edge on the end face is a sub-blade. When the end mill without the center edge is working, it cannot make a feed motion along the axial direction of the milling cutter. End mills are currently widely used in various sectors such as automobile manufacturing, logistics, molds, machinery, etc., and because of the increasing use of various aspects, the application requirements are also increasing. Therefore, various problems that are common in the use of end mill applications are summarized and answered.

نهاية الأميال

[س] كيف يجب طحن Ø12 من أسنان طاحونة النهاية؟

[الإجابة] أولاً ، يجب أن تكون عجلة الرمل مطحونة ، حافة الطحن مائلة قليلاً ، قاطع الطحن ، يجب أن تنتبه الشفرة ، يجب أن يكون الخارج أعلى من الداخل ... يجب ألا يكون المنحدر الداخلي مائلًا جدًا ، ربما تمامًا مثل هذا ، لا يزال يتعين على هذا أن يطحن المزيد من الممارسة فقط.

[س] ما هي المطحنة النهائية وما هو قاطع الطحن القرصي؟ ماهو الفرق؟

[الإجابة] تُستخدم المطاحن النهائية بشكل عام لطحن الأسطح الطرفية ، بدلاً من قواطع طريق المفاتيح لفتحات الطحن. يتم استخدام قاطع الطحن القرصي بشكل أساسي لطحن الأسطح الطرفية الكبيرة ، لأن الطحن المستقيم لقاطع الطحن القرصي كبير بشكل عام ، وسطح نهاية الطحن أسرع للطحن ، وقاطع طحن شفرة المنشار يستخدم بشكل عام للطحن.

[س] لماذا لا يمكن قطع طاحونة نهاية عموديا؟

[الإجابة] عندما تدور المطحنة النهائية ، تكون نقطة المنتصف للحافة السفلية ثابتة نسبيًا. لا تحتوي على أي آلية وإزالة للرقائق ، لذلك لا يمكن قطعها عموديًا.

[Q] How is the feed rate of the مطحنة نهاية determined?

[الإجابة] ينبغي النظر في اختيار كمية القطع جنبًا إلى جنب مع عوامل مثل الأداة وقطعة العمل وأداة الماكينة. حافة القطع الرئيسية للمطحنة النهائية هي الحافة المحيطية. تبلغ العلف لكل سن بشكل عام حوالي 0.1 أثناء الإنهاء. يتم تحديد الكمية بشكل عام من 0.25 إلى 0.3 مم. على وجه التحديد ، يجب أن تتطابق مع معلمات القطع مثل سرعة القطع والعمق المحوري للقطع والعمق الشعاعي للقطع.

المطاحن الكرة الأنف

[س] ما هو الفرق بين المطحنة النهائية والمطحنة الطرفية الكروية ومبدأ الاختيار؟

[الإجابة] المطاحن النهائية وطواحين الكرة الطرفية ، أحدهما هو رأس الكرة ، والآخر هو القاع المسطح ، والمطحنة النهائية تستخدم أساسًا للمعالجة التقليدية ، ويمكن استخدام قاطع الطحن بنهاية الكرة لطحن السطح.

[س] ما هو الفرق بين كوليت لطاحونة النهاية وكوليت للصنبور؟ هل يجب عليك استخدام مقبض الشركة عند النقر؟

[إجابة] على الرغم من أنه يمكن استخدام كوليت لعقد المطحنة الطرفية للساق المستقيمة لإمساك الصنبور للتنصت الصلب ، إلا أن التأثير ليس جيدًا ، وعمومًا لا يمثل صنبور القطر الصغير مشكلة ؛ كوليت ER للصنبور مع أخدود مربع أي أن وظيفة الحد المسطح الذيل لمقبض الصنبور متاحة الآن في الشركات المصنعة للأدوات بشكل عام.

[Q] What is the difference between a reamer and an end mill?

[Answer] The reamer is a straight edge and the end mill is a spiral edge. The milling cutter has a bottom edge and the reamer does not! The reamer is used to finish the hole, while the milling cutter can be milled, washed, and side washed! Use is different!

[س] كيف يتم تحديد معدل تغذية المطحنة النهائية؟

[الإجابة] ينبغي النظر في اختيار كمية القطع جنبًا إلى جنب مع عوامل مثل الأداة وقطعة العمل وأداة الماكينة. حافة القطع الرئيسية للمطحنة النهائية هي الحافة المحيطية. تبلغ العلف لكل سن بشكل عام حوالي 0.1 أثناء الإنهاء. يتم تحديد الكمية بشكل عام من 0.25 إلى 0.3 مم. على وجه التحديد ، يجب أن تتطابق مع معلمات القطع مثل سرعة القطع والعمق المحوري للقطع والعمق الشعاعي للقطع.

[Q] What are the steps for milling the end mill?

[Answer] First install the end mill, then move the end mill to the top of the workpiece to be milled, gently lick the upper surface of the workpiece with the end teeth of the end mill, and then lift the dial of the milling machine Zero; then move the end mill to the side of the workpiece, lower the end mill to the side of the workpiece, then gently lick the side of the workpiece with the side of the cutter, and set the handle dial in the corresponding direction to zero, then Start milling the steps. The depth of the knife is determined according to the size of the machining allowance, the strength of the material, and the size of the milling cutter. After eating from at least one knife, it is completed by dividing into several knives.

[Q] What is the difference between an end mill and a keyway cutter?

[Answer] The main difference between the end mill and the keyway cutter is that the end mill is used to machine flat or cylindrical surfaces, so its outer diameter is relatively loose, and the keyway cutter is used to machine the keyway. The outer diameter dimension directly affects the mating quality of the keyway and the key, so the tolerance is stricter; in addition, the keyway milling cutter has only two blade belts for machining holes, and the end mill has more than two blade belts. The end face of the end mill has a center hole, and the end face of the keyway cutter has no center hole. Therefore, the end mill is not able to feed directly down, deep down, and the center hole will withstand. The keyway cutter can be fed directly down. In addition, the keyway milling cutter, as the name implies, is used to mill the keyway, so the dimensional accuracy of the outer diameter is very high, and generally can reach an accuracy of about 0.01 mm.

اترك تعليقاً

لن يتم نشر عنوان بريدك الإلكتروني. الحقول الإلزامية مشار إليها بـ *