{"id":3215,"date":"2019-01-03T01:25:43","date_gmt":"2019-01-03T01:25:43","guid":{"rendered":"https:\/\/www.mcctcarbide.com\/?p=3215"},"modified":"2021-02-03T02:30:29","modified_gmt":"2021-02-03T02:30:29","slug":"hard-to-pick-out-suitable-end-mills-these-basics-may-help","status":"publish","type":"post","link":"https:\/\/www.meetyoucarbide.com\/de\/hard-to-pick-out-suitable-end-mills-these-basics-may-help\/","title":{"rendered":"Es ist schwer, geeignete Schaftfr\u00e4ser auszuw\u00e4hlen? Diese Grundlagen k\u00f6nnen helfen"},"content":{"rendered":"
\n

Hard to Pick Out Suitable End Mills<\/a>? These Basics May Help<\/strong><\/h2>\n\n\n\n

The main cutting edge of the end mill is a cylindrical surface, and the cutting edge on the end face is a sub-blade. When the end mill without the center edge is working, it cannot make a feed motion along the axial direction of the milling cutter. End mills are currently widely used in various sectors such as automobile manufacturing, logistics, molds, machinery, etc., and because of the increasing use of various aspects, the application requirements are also increasing. Therefore, various problems that are common in the use of end mill applications are summarized and answered.<\/p>\n\n\n\n

\"Schaftfr\u00e4ser<\/figure>\n\n\n\n

[F] Wie sollte der \u00d812 der beiden Z\u00e4hne des Schaftfr\u00e4sers geschliffen werden?<\/p>\n\n\n\n

[Answer] First, the sand wheel should be ground, the edge of the grinding is a little angled, the milling cutter, the blade should pay attention, the outside should be higher than the inside… The slope inside should not be too oblique, probably just like this, this still has to grind more Practice only.<\/p>\n\n\n\n

[F] Was ist ein Schaftfr\u00e4ser und was ein Scheibenfr\u00e4ser? Was ist der Unterschied?<\/p>\n\n\n\n

[Antwort] Schaftfr\u00e4ser werden in der Regel zum Fr\u00e4sen von Stirnfl\u00e4chen verwendet, nicht Keilnutfr\u00e4ser zum Fr\u00e4sen von Nuten. Der Scheibenfr\u00e4ser wird haupts\u00e4chlich zum Fr\u00e4sen gro\u00dfer Stirnfl\u00e4chen verwendet, da das gerade Fr\u00e4sen des Scheibenfr\u00e4sers im Allgemeinen gro\u00df ist, die Fr\u00e4sstirnfl\u00e4che zum Fr\u00e4sen schneller ist und der S\u00e4geblattfr\u00e4ser im Allgemeinen zum Fr\u00e4sen verwendet wird.<\/p>\n\n\n\n

[Q] Why can’t the end mill cut vertically?<\/p>\n\n\n\n

[Antwort] Wenn sich der Schaftfr\u00e4ser dreht, ist der Mittelpunkt der Unterkante relativ statisch. Es hat keine maschinelle Bearbeitbarkeit und Spanabfuhr, daher kann es nicht vertikal geschnitten werden.<\/p>\n\n\n\n

[Q] How is the feed rate of the Schaftfr\u00e4ser<\/a> determined?<\/p>\n\n\n\n

[Antwort] Die Auswahl der Schnittmenge sollte zusammen mit den Faktoren wie Werkzeug, Werkst\u00fcck und Werkzeugmaschine betrachtet werden. Die Hauptschneide des Schaftfr\u00e4sers ist die Umfangskante. Der Vorschub pro Zahn betr\u00e4gt beim Schlichten im Allgemeinen etwa 0,1. Die Menge wird im Allgemeinen aus 0,25 bis 0,3 mm ausgew\u00e4hlt. Konkret sollte sie auf die Schnittparameter wie Schnittgeschwindigkeit, axiale Schnitttiefe und radiale Schnitttiefe abgestimmt werden.<\/p>\n\n\n\n

\"Kugelnasenm\u00fchlen\"<\/figure>\n\n\n\n

[F] Was ist der Unterschied zwischen dem Schaftfr\u00e4ser und dem Kugelschaftfr\u00e4ser und seinem Auswahlprinzip?<\/p>\n\n\n\n

[Antwort] Schaftfr\u00e4ser und Kugelkopffr\u00e4ser, einer ist der Kugelkopf, einer ist der flache Boden, der Schaftfr\u00e4ser dient haupts\u00e4chlich der konventionellen Bearbeitung und der Kugelkopffr\u00e4ser kann zum Fr\u00e4sen der Oberfl\u00e4che verwendet werden.<\/p>\n\n\n\n

[F] Was ist der Unterschied zwischen der Spannzange f\u00fcr den Schaftfr\u00e4ser und der Spannzange f\u00fcr den Gewindebohrer? M\u00fcssen Sie beim Zapfen das Firmenhandle verwenden?<\/p>\n\n\n\n

[Antwort] Obwohl die Spannzange zum Halten des Schaftfr\u00e4sers mit geradem Schaft verwendet werden kann, um den Gewindebohrer f\u00fcr starres Gewindeschneiden zu halten, ist die Wirkung nicht gut, im Allgemeinen ist der Gewindebohrer mit kleinem Durchmesser kein Problem; Die ER-Spannzange f\u00fcr den Gewindebohrer ist mit einer Vierkantnut ausgestattet. Das hei\u00dft, die Flachschwanzbegrenzungsfunktion des Gewindebohrergriffs ist jetzt bei allgemeinen Werkzeugherstellern verf\u00fcgbar.<\/p>\n\n\n\n

[Q] What is the difference between a reamer and an end mill?<\/p>\n\n\n\n

[Answer] The reamer is a straight edge and the end mill is a spiral edge. The milling cutter has a bottom edge and the reamer does not! The reamer is used to finish the hole, while the milling cutter can be milled, washed, and side washed! Use is different!<\/p>\n\n\n\n

[F] Wie wird die Vorschubgeschwindigkeit des Schaftfr\u00e4sers bestimmt?<\/p>\n\n\n\n

[Antwort] Die Auswahl der Schnittmenge sollte zusammen mit den Faktoren wie Werkzeug, Werkst\u00fcck und Werkzeugmaschine betrachtet werden. Die Hauptschneide des Schaftfr\u00e4sers ist die Umfangskante. Der Vorschub pro Zahn betr\u00e4gt beim Schlichten im Allgemeinen etwa 0,1. Die Menge wird im Allgemeinen aus 0,25 bis 0,3 mm ausgew\u00e4hlt. Konkret sollte sie auf die Schnittparameter wie Schnittgeschwindigkeit, axiale Schnitttiefe und radiale Schnitttiefe abgestimmt werden.<\/p>\n\n\n\n

[Q] What are the steps for milling the end mill?<\/p>\n\n\n\n

[Answer] First install the end mill, then move the end mill to the top of the workpiece to be milled, gently lick the upper surface of the workpiece with the end teeth of the end mill, and then lift the dial of the milling machine Zero; then move the end mill to the side of the workpiece, lower the end mill to the side of the workpiece, then gently lick the side of the workpiece with the side of the cutter, and set the handle dial in the corresponding direction to zero, then Start milling the steps. The depth of the knife is determined according to the size of the machining allowance, the strength of the material, and the size of the milling cutter. After eating from at least one knife, it is completed by dividing into several knives.<\/p>\n\n\n\n

[Q] What is the difference between an end mill and a keyway cutter?<\/p>\n\n\n\n

[Answer] The main difference between the end mill and the keyway cutter is that the end mill is used to machine flat or cylindrical surfaces, so its outer diameter is relatively loose, and the keyway cutter is used to machine the keyway. The outer diameter dimension directly affects the mating quality of the keyway and the key, so the tolerance is stricter; in addition, the keyway milling cutter has only two blade belts for machining holes, and the end mill has more than two blade belts. The end face of the end mill has a center hole, and the end face of the keyway cutter has no center hole. Therefore, the end mill is not able to feed directly down, deep down, and the center hole will withstand. The keyway cutter can be fed directly down. In addition, the keyway milling cutter, as the name implies, is used to mill the keyway, so the dimensional accuracy of the outer diameter is very high, and generally can reach an accuracy of about 0.01 mm.<\/p>\n<\/div>","protected":false},"excerpt":{"rendered":"

Hard to Pick Out Suitable End Mills? These Basics May Help The main cutting edge of the end mill is a cylindrical surface, and the cutting edge on the end face is a sub-blade. When the end mill without the center edge is working, it cannot make a feed motion along the axial direction of…<\/p>","protected":false},"author":2,"featured_media":19371,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[92],"tags":[],"jetpack_featured_media_url":"https:\/\/www.meetyoucarbide.com\/wp-content\/uploads\/2019\/01\/1-2.png","jetpack_sharing_enabled":true,"_links":{"self":[{"href":"https:\/\/www.meetyoucarbide.com\/de\/wp-json\/wp\/v2\/posts\/3215"}],"collection":[{"href":"https:\/\/www.meetyoucarbide.com\/de\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.meetyoucarbide.com\/de\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.meetyoucarbide.com\/de\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/www.meetyoucarbide.com\/de\/wp-json\/wp\/v2\/comments?post=3215"}],"version-history":[{"count":0,"href":"https:\/\/www.meetyoucarbide.com\/de\/wp-json\/wp\/v2\/posts\/3215\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.meetyoucarbide.com\/de\/wp-json\/wp\/v2\/media\/19371"}],"wp:attachment":[{"href":"https:\/\/www.meetyoucarbide.com\/de\/wp-json\/wp\/v2\/media?parent=3215"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.meetyoucarbide.com\/de\/wp-json\/wp\/v2\/categories?post=3215"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.meetyoucarbide.com\/de\/wp-json\/wp\/v2\/tags?post=3215"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}